When, it’s generally best to stay with the same (gas or electric) unless there’s good reason to switch. It’s also a good idea to check with a local plumbing inspector. They can share the local plumbing codes with you, as well as let you know if you’ll need a municipal permit.Another point to consider is how to If you hire a professional you won’t need to worry about this because they will haul your old water heater away for you. Still, if you enjoy doing projects yourself, and you would like to save yourself some money, replacing a gas water heater is not hard.What to Consider Before Installing your Gas Water HeaterIf your water heater is over 10 years old, there’s a good chance that it has and it will need to be replaced.
However, before you buy a new water heater, it’s worth your effort to troubleshoot the problem. If your many times the issue is repairable. However, if the source of the leak is from the tank itself, you will need to replace the unit. Tools and Supplies Needed for Gas Water Heater Installation. Tape measure and pencil. Wire brush. Utility knife.
Wrench. 3/8″ Nut driver or a drill with a 3/8″ bit. Pipe Joint Compound: Gas plumbers tape (optional), or teflon tape (optional). Self tapping sheet metal screws.
Soap & Water: Leak detection solution (optional). Earthquake Straps. Adjustable vent pipe (Ameri-vent). 2 Flexible hoses. Flexible gas lineA Few Things to Keep in Mind Before Installing your Gas Water Heater. Check the label on your old water heater. It should list the annual energy useage and the tank size.
Attach the vent hood over the flue on the top of the water heater. Follow the instructions that came with your water heater, as the process varies among different manufacturers.
Use self-tapping sheet metal screws to secure the vent hood into place.Step 4Install the Vent Piping. If your vent pipe is in good condition, you should be able to reuse it with your new water heater. Check your water heaters instruction manual for the correct vent pipe diameter. A reducer should NOT be used if the recommended vent pipe diameter is larger than the vent hood. Using adjustable vent pipe, insert one end into the water heater vent hood and begin attaching the other pipe sections. Be sure to check your water heater manufacturer manual for the correct diameter. Adjust the elbows prior to installing to allow the vent pipe to align as closely to straight as possible.
Secure all the vent pipe sections by pushing them together so that each fits tightly to the other. Use self-tapping sheet metal screws to secure the vent sections to the water heater vent hood and the other vent sections. Use at least 2 screws at each connection.
Check your local code for requirements.Step 5Install the Gas Connection. Double check that the gas supply is in the OFF position. Using a wire brush, clean the pipe fitting on the supply pipe. Flush the line by opening and closing the valve. Remove the sticker and plug on the gas control valve. This is where the gas line will contect.
Unscrew the gas nipple on the flexible gas line. Flexible gas lines are required in many areas, especially areas prone to earthquakes. Free download viber for my nokia c3.
It is always a good idea to check if they are allowed in your area. Paint pipe joint compound onto the thread of the gas nipple. Avoid covering the first few threads with pipe joint compound as shown in the video. We recommend using Gas Plumbers Tape which is yellow, and not as messy. NEVER use white Teflon tape. Attach the gas nipple into the gas control valve. Tighten the gas nipple with a wrench.
It should be FAIRLY TIGHT. Be careful of damaging the gas control valve while tightening. We recommend tightening the nipple with 2 wrenchs to prevent damage to the gas control valve.
One wrench on the nipple and the other holding the gas control valve. Attach the gas flex connector line to the gas line and the water heaters gas control valve. Be careful not to kink the line. Loop the excess line if necessary. Hand tighten the connectors and then, use a wrench to tighten slightly tighter.
Do NOT turn on the gas.Step 6Fill the Tank. Open the water inlet valve and begin filling the tank with water.
Open a hot water faucet, this will alert you that the tank is full. Check for leaks on each end of the two flexible water lines. When water runs from the hot water faucet, the tank is full. Allow the water to run for several minutes to eliminate the air in the tank. The water will sputter until the tank is full and all air has been bled from the tank and lines.Step 7Connect the Earthquake Straps. Pull the earthquake straps around the water heater and connect them together.
Do not pull the straps too tight. They should be snug, but not too tight.
Use clips to fasten the excess strap.Step 8Connect the T&P Drain Pipe. You may be able to reuse your from your old water heater. If you need to make a new one, measure and cut a copper pipe with a tube cutter. If you do not have a floor drain, place a bucket under the T&P drain pipe.